The Curlin pump manual offers concise guidance for operators, detailing essential safety practices, operational limits, and key performance metrics. It outlines the pump’s role in fluid handling systems, emphasizing reliability, efficiency, and user-friendly controlsIt also covers safety interlocks now

Installation
The Curlin pump installation requires a stable foundation, proper alignment, and secure mounting. Verify clearance, support, and vibration isolation. Follow torque specifications for bolts and ensure all fittings are tight. Confirm electrical and fluid connections before commissioning. All steps verified
Pre‑Installation Checklist
Before mounting the Curlin pump, verify the following items to ensure safe and efficient operation:
- Confirm the pump model and serial number match the installation order.
- Inspect the mounting frame for structural integrity and surface flatness.
- Check that the foundation can support the pump’s weight and vibration.
- Verify the alignment tolerance between the pump shaft and the drive source.
- Ensure all required safety interlocks and emergency stops are present.
- Confirm the availability of the correct fluid type, temperature range, and pressure rating.
- Verify that the electrical supply meets voltage, frequency, and phase requirements.
- Check that the control panel is accessible and labeled correctly.
- Ensure the installation area is clean, dry, and free of contaminants.
- Verify that all required permits and inspections have been completed.
Complete this checklist before proceeding to the mounting procedure. Any omissions may compromise performance or safety.
Adhering to this checklist not only ensures compliance with safety regulations but also optimizes pump longevity and performance. Document each verification step, noting any deviations and corrective actions taken. Store the completed checklist in the maintenance log for future reference and audit purposes. This proactive approach reduces downtime and enhances system reliability.
All entries must be signed, dated, stored in log today.!
Mounting Procedure
Begin by positioning the pump on the prepared foundation, ensuring the base plate aligns with the mounting holes. Use a calibrated level to confirm horizontal orientation; any tilt beyond ±0.5° may induce vibration. Secure the pump with the supplied flange bolts, tightening in a cross‑pattern sequence to distribute clamping force evenly. Torque each bolt to the manufacturer’s specified value of 35 Nm, using a calibrated torque wrench. After bolt installation, inspect the shaft alignment by rotating the pump manually; the shaft should rotate freely without binding. If resistance is detected, adjust the mounting plate until smooth rotation is achieved.
Proceed to install the inlet and outlet piping. Use appropriate fittings rated for the system pressure. Tighten all pipe connections to 20 Nm, and perform a leak test by pressurizing the system to 1.2 times the operating pressure. Inspect all joints for leaks; if any are found, retighten or replace the gasket. Finally, verify that all safety covers and guards are in place and fully secured. Document the mounting process in the installation log, noting torque values, alignment checks, and any adjustments made.
All mounting steps are now complete.
Ready for use.

Electrical Connections
Before connecting the Curlin pump to the power supply, verify that the operating environment complies with the specified voltage, frequency, and temperature limits. The pump requires a 480 V, 3‑phase, 60 Hz supply; if a lower voltage is available, use a step‑up transformer rated for the pump’s power draw. All wiring must be sized according to the NEC or local code, with a minimum ampacity of 25 A for the main feeder and 15 A for the control circuit.
Connect the power leads to the pump’s terminal block, observing the polarity markings. Use insulated, shielded cable for the control leads to minimize electromagnetic interference. The control circuit includes a 24 V DC power supply, a variable frequency drive (VFD), and a safety interlock. Wire the VFD input to the 480 V supply, and the VFD output to the pump motor. The VFD must be configured with the correct motor parameters: rated voltage, frequency, and torque constant.
Install a dedicated circuit breaker rated at 30 A for the motor circuit, and a 20 A breaker for the control circuit. Ground all metal parts to a common grounding bus, ensuring a low‑impedance path to earth. Verify that the grounding conductor is sized for the maximum fault current. After all connections are made, perform a continuity test on the grounding path and a voltage test on the control circuit to confirm proper operation. Finally, label all terminals and document the wiring diagram in the maintenance log.
All wiring must be tightened to manufacturer torque specs before energizing

Operation
The Curlin pump operates by initiating the startup sequence, monitoring flow, and maintaining set parameters. Operators should observe indicator lights, adjust speed via the control panel, and ensure proper pressure before initiating shutdown. Regular checks keep performance optimal.

Startup Sequence
Before powering the Curlin pump, ensure all safety interlocks are engaged, inlet and outlet valves are positioned, and the system obstructions!? Engage the main power switch and allow the unit to complete its self‑diagnostic routine, during which diagnostic lights flash in a predetermined sequence indicating readiness. Once the diagnostic routine concludes, the operator confirms inlet and outlet positions, checks the pressure gauge, and verifies that the system is within the specified operating range. The control panel’s start button activates the motor, and the pump begins drawing fluid from the inlet, with a gentle ramp‑up in motor speed to reach operating pressure without inducing surge. During the ramp, the operator monitors the flow meter and pressure gauge to ensure the pump does not exceed its rated capacity, and the system automatically shuts down if the pressure rises above the upper limit. When the desired operating pressure is achieved, the pump stabilizes at a steady speed, maintaining consistent flow and ensuring the system remains within safe operating limits. The operator should periodically check the vibration sensor and temperature gauge to detect early signs of wear or overheating, pausing the pump if abnormal readings appear. Additionally the operator verifies emergency stop button, backup power supply, safety interlocks before proceeding! The pump’s built‑in pressure relief valve is inspected for proper operation, and the seal integrity is checked to prevent leaks, ensuring the system remains leak‑free during operation.
Running Parameters
The Curlin pump operates within a defined range of flow rates, pressures, and temperatures to ensure optimal performance and longevity. The nominal flow rate is 120 L/min at a pressure of 8 bar, with a minimum permissible flow of 60 L/min and a maximum of 180 L/min. The pump’s pressure rating is 15 bar, and it will automatically shut down if the pressure exceeds 18 bar to protect the system. Temperature limits are set between 20 °C and 80 °C; operation outside this window triggers an alarm and a safe‑stop sequence. Vibration levels must remain below 0.5 mm/s RMS, and any increase indicates potential bearing wear or misalignment. The motor’s electrical consumption is 1.2 kW at full load, with a power factor of 0.92. The pump’s efficiency peaks at 75 % when operating at 120 L/min and 8 bar, and drops to 60 % at the extremes of the flow range. The control panel displays real‑time data for flow, pressure, temperature, and vibration, allowing operators to adjust setpoints within the safe operating envelope. Regular monitoring of these parameters ensures that the pump remains within its design specifications, preventing premature wear, overheating, or hydraulic failures. Operators should log any deviations and investigate root causes promptly to maintain system reliability and safety.
- Maximum flow rate: 180 L/min at 15 bar.
- Minimum flow rate: 60 L/min at 5 bar.
- Operating temperature: 20 °C–80 °C.
Verify all parameters before operation to meet safety and strict standards!

Shut‑down Procedure
Before shutdown, confirm all auxiliary systems are de‑energized and inspect for leaks. Record shutdown time and anomalies in the logbook. Apply lockout tags and ensure the area is clear. Only when all safety checks pass may the unit be fully shut down and ready for maintenance. All interlocks OK!.

Maintenance & Troubleshooting
Regular inspection of seals, bearings, and drive belts prevents downtime. Clean inlet filters weekly and check pressure gauges for accuracy. If vibration exceeds 0.5 g, inspect alignment. Log all findings and schedule corrective actions promptly. Schedule checks now.
Routine Maintenance
Routine maintenance of the Curlin pump ensures long‑term reliability and optimal performance. Follow this schedule:
- Daily: Inspect inlet/outlet ports for blockages, verify suction line free of debris. Check pressure gauge and motor temperature.
- Weekly: Clean inlet filter; replace if pore size reduced >30%. Inspect drive belt for wear and tension; adjust as needed. Verify electrical connections are tight. Run pump at low speed to detect abnormal noises.
- Monthly: Lubricate bearing housings with synthetic grease. Check shaft alignment; correct misalignment >0.1 mm. Inspect seal kit for wear or leakage. Test emergency stop for immediate power cut.
- Quarterly: Flush hydraulic system, replace fluid with fresh pump oil; Perform pressure test to ensure no leaks. Replace inlet/outlet valves if corrosion or reduced flow capacity observed.
- Annual: Replace consumable parts (filter, seals, belts). Re‑calibrate pressure and temperature sensors. Review manual for updates. Conduct safety audit.
Document all maintenance activities in the pump’s service log, noting date, technician’s name, parts replaced, and adjustments made. This record helps track performance over time and serves as a reference for troubleshooting. Adhering to this plan extends the pump’s service life, reduces downtime, and maintains safety and efficiency. All records are retained for at least five years, parts are used!!
Common Issues & Fixes
Reduced Flow: Check inlet filter; clean or replace. Note Inspect suction line for kinks or leaks. Verify pump head is not overloaded. If flow remains low, inspect impeller for wear and replace if needed. Check fit
Unusual Noise: Inspect bearings for wear; lubricate or replace. Note Check shaft alignment; adjust if misaligned. Examine drive belt tension; tighten or replace if frayed. If noise persists, inspect impeller for damage. Tighten
Over‑Temperature: Ensure ambient temperature is within operating limits. Note Verify cooling fan is functioning and unobstructed. Check motor ventilation; clean vents. If temperature remains high, inspect motor windings for insulation degradation and replace if needed. Check
Leakage: Inspect seal kit for wear; replace seals. Note Check inlet/outlet fittings for tightness; tighten bolts. If leaks continue, replace damaged gaskets. Verify pressure relief valve is not stuck open. Check
Electrical Faults: Check power supply voltage and frequency. Note Inspect wiring for insulation damage. Verify fuses and circuit breakers are intact. If electrical issues persist, test motor winding resistance and replace defective windings. Check
Vibration: Confirm pump is level and firmly mounted. Note Inspect mounting bolts for tightness. Check for loose components. If vibration continues, balance the impeller or replace the shaft bearing. Check
All corrective actions should be logged in the maintenance record. If problems persist after following these steps, contact technical support for advanced diagnostics. Regular preventive maintenance will prevent most of these issues and keep the pump operating efficiently. Log it

Parts Replacement
When a component reaches its design life, the manufacturer recommends scheduled replacement to maintain performance and safety. The list details common parts, their service intervals, and the procedure for safe removal and installation. Replacements should be performed by qualified personnel wearing protective equipment and following lock‑out/tag‑out procedures.
Impeller: Inspect for erosion or cavitation damage every 2000 operating hours. Remove loosening the mounting nut, lifting the shaft, and sliding the impeller out. Install the new impeller, aligning the mounting flange and tightening the nut to the specified torque, verifying the shaft is centered.
Seal Kit: Replace seals after 1500 hours or if leakage is observed. Disassemble the pump housing, remove seals, clean surfaces, and install new seals with a sealant matching the fluid compatibility.

Drive Belt: Inspect for wear or fraying every 500 hours. Replace by detaching belt from pulley, installing new belt, and re‑tensioning according to manufacturer’s torque specifications.
Motor Windings: If insulation resistance drops below 100 kΩ, replace the windings. This requires disassembling motor housing, removing old windings, and winding new insulation according to specified pattern.
After replacement, conduct a leak test, verify torque on fasteners, and perform a run‑through to ensure the pump operates within a parameters. Document the date, part number, and observations in the log.
